Brother MFC 495CW
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
An error in the cartridges, the heads clogged by dry ink, a very low level in your consumables, a bad connection between the computer and the printer, a damaged cable, a jam in the print queue…, there are many reasons why your Brother printer may stop printing or print poorly even though you have not jumped the ink …
The main culprits are: Weak Wi-Fi signal – Try moving your printer closer to the Wi-Fi router. Incorrect Wi-Fi network settings – See step 2. Software issues such as out-of-date firmware or drivers – See step 3.
Faulty power cords and connections are an uncommon but possible cause of a printer not turning on. Before suspecting a cord failure, ensure that there is power to the wall outlet and there are no conditions preventing the printer from turning on. Testing by substitution can confirm if a cord connection is the problem.
1: Check Printer Power, Cables, and Paper
Check that the correct paper is properly loaded into the printer and is not jammed. Replacing damaged cables, plugging in loose or disconnected cables, and fixing paper jams as necessary may resolve the issue.
There are many factors that determine the actual drum life, such as the temperature, humidity, type of paper, type of toner used, number of pages per print job and so on. Under ideal conditions, the average drum life is estimated at approximately 12,000 pages.
Turning the power ON/OFF while the print monitor screen is displayed may cause the printer driver to go off-line and make printing impossible. In this case, open the [Printers / Printers and Faxes / Devices and Printers] folder on the computer and check if your printer driver is shown as off-line.
If your wireless printer isn`t printing, be sure to check your settings. Make sure your Wi-Fi is enabled, and then check to be sure you`re connected to the correct Wi-Fi network. You can often check your connectivity by printing a network configuration sheet by selecting this option from the printer`s display menu.
If the LCD display is blank, follow the steps listed below: Verify the power cord is connected to the back of the machine and the AC power outlet. If the power cord is connected to a surge protector or power switch, remove the cord from the device and connect it directly to the outlet. This is for testing purposes.
Remove the power cord for at least 30 seconds. Press and hold the ON/OFF button down, and then insert the power cord back into the Brother machine. Do not release the ON/OFF button until the machine has been powered on completely or after 15 seconds. Repeat this procedure up to three times if necessary.
Printer sleep mode
Check that the printer does not have sleep mode enabled: Go to Control Panel > Devices and Printers. Right-click the printer in question, then select Printer Preferences. Look for an option to disable sleep or time-out mode.
The fuse protects your printer from short circuits and power overload. It is placed between the power outlet and the switch on the left side of the printer. If your machine does not start after pressing the power switch, at first you should check if the power cable is connected to a power source.
A component found in electrostatic printers, laser printers, and xerographic printers and photocopiers. The fuser unit is used to permanently bond toner to a substrate by applying heat and pressure. A fuser unit is made up of two rollers; one to apply heat and one to apply pressure.
If the LCD display is blank, follow the steps listed below: Verify the power cord is connected to the back of the machine and the AC power outlet. If the power cord is connected to a surge protector or power switch, remove the cord from the device and connect it directly to the outlet. This is for testing purposes.
Receiving a print job or pressing a control panel key wakes up the machine from Sleep mode to Ready mode. You can choose how long the machine must be idle before it goes into sleep mode. When the machine receives a print job the timer will be reset.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Brother HL-2170W — 2nd sheet printing causes jam
ANSWER : I tried Angry Larry’s link to Photobucket but there’s an error message. I tried rocklobster’s link to Imageshack, but it’s for a different printer. Can someone please send me the photos to fix this issue with my Brother HL-2170W? My email is [email protected] Very much appreciated!
Read Full Q/A … :
Brother MFC 495CW
Changing Language of Printer Brother MFC-J5910DW
ANSWER : I have a 2720DW from the netherlands it is a french model an it has the code 0009
Read Full Q/A … :
Brother MFC 495CW
Brother J315W – paper misfeed
ANSWER : I have the same problem: whether printing or copying, the paper feeds almost up to the print head and then stops with a paper jam error. Can’t find any bits of paper stuck anywhere. Sure would appreciate some help. DCP-J315W
Read Full Q/A … :
Brother MFC 495CW
Brother MFC-J6510DW extra paper tray.
ANSWER : There clearly was a similar problem couldn’t enter in to a ditch of benefit drawing up a strategy. A pal gave this http://put-call-options.com site to select an appropriate technique and I have chosen for themselves the optimum and successful naybolee. I hope I served you with your problem. Thanks for attention)))
Read Full Q/A … :
Brother MFC 495CW
4F displayed on Brother 990CW printer?
ANSWER : That’s a printhead error.
Read Full Q/A … :
Brother MFC 495CW
Brother MFC-L2740DW maintenance mode
ANSWER : Hi,
Read Full Q/A … :
Brother MFC 495CW
Brother MFC 8220
ANSWER : This problem is normally caused by the fuser. There’s a brown driver gear who frequently broke and you’ll be obliged to replce it to take care of the problem.
Read Full Q/A … :
Brother MFC 495CW
Brother HL-2270dw Printer
ANSWER : maybe you can download here Brother HL-2270dw Driver Download
Read Full Q/A … :
Brother MFC 495CW