Brother DCP J315W
Experienced technical support provide their insights in answering this question :
I have the same problem: whether printing or copying, the paper feeds almost up to the print head and then stops with a paper jam error. Can’t find any bits of paper stuck anywhere. Sure would appreciate some help. DCP-J315W
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
The message Paper Jam may appear on the display if the Brother machine is not feeding paper correctly, paper scraps have become stuck in the print head path, the paper is not loaded properly in the paper tray, the jam clear cover located in the back of the machine, is not installed properly or the PE Actuator is …
Sometimes a paper jam error persists even though there is no jammed paper (false paper jam). Reset the printer, which might clear a false paper jam error, and then try to print again. With the printer turned on, disconnect the power cord from the printer. Unplug the power cord from the power source.
During a print job, the printer stops feeding pages, and a Paper Jam error message displays on the printer control panel. This indicates that paper might be jammed inside the printer. note: Paper jams can be real or false. The printer might report a paper jam even when there is no jammed paper.
A paper jam is when paper or other printed material gets stuck or lodged in a printer and cannot eject.
A piece of paper stuck in the paper tray or inside the printer can create a paper jam. Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer.
Cause 1: The photo bypass tray is located at the wrong position. Cause 4: Paper dust has accumulated on the surface of the paper pick-up rollers. Cause 6: The paper tray was not fully inserted. NOTE: Illustrations shown below are from a representative product and may differ from your Brother machine.
Clean the print head, if necessary. Make sure the paper size, orientation, and layout settings in your printer software are correct. Make sure your document does not contain blank pages. If your printer software has a Preview option, you can check for blank pages before you print and remove them, if necessary.
Capacitive sensors can detect objects that have a dielectric constant that is different from air. Hence, these sensors can detect objects made from a wide variety of materials such as plastic, paper, wood, etc.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Brother J315W – paper misfeed
ANSWER : I have the same problem: whether printing or copying, the paper feeds almost up to the print head and then stops with a paper jam error. Can’t find any bits of paper stuck anywhere. Sure would appreciate some help. DCP-J315W
Read Full Q/A … :
Brother DCP J315W
My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.
Read Full Q/A … :
Brother DCP J315W
Brother MFC-J6510DW extra paper tray.
ANSWER : There clearly was a similar problem couldn’t enter in to a ditch of benefit drawing up a strategy. A pal gave this http://put-call-options.com site to select an appropriate technique and I have chosen for themselves the optimum and successful naybolee. I hope I served you with your problem. Thanks for attention)))
Read Full Q/A … :
Brother DCP J315W
Brother Hl-2040 paper over feed
ANSWER : Your instructions saved me..I had the board off 3 times before i saw your pix….thanks so much!
Read Full Q/A … :
Brother DCP J315W
Multiple paper feed
ANSWER : Most likely the pickup roller solenoid is sticking. The way it works is the solenoid energizes, pulling down a metal plate that releases the pickup roller. There is some foam on the base to quiet the clicking sound. The foam deteriorates and the plate sticks to the gooey residue. This allows the pickup roller to continue to turn instead of stopping after one revolution when the plate springs back up. That results in multiple paper being fed. Solution is to find the solenoid, which is at the end of the pickup roller shaft. Remove the sticky foam and preferably replace it with some thin sticky backed felt. You can find it at a hardware store as it is used on the bottom of chair legs.
Read Full Q/A … :
Brother DCP J315W
Error Message "Paper out" when paper loaded
ANSWER : Check your paper tray settings as printer may be looking for paper from the manual feed tray on top of printer.
Read Full Q/A … :
Brother DCP J315W
Paper jam in front of print head. HELP URGENT Please
ANSWER : I am 99% sure you don’t have a problem with a sensor. Having no idea what you do in the cleaning process, and not being able to look at the printer, there is no way to help or advise you.
Read Full Q/A … :
Brother DCP J315W
Error message to load paper and push OK, but not out of paper
ANSWER : I assist the binary options for a long time, and only half this past year I decided to alter the strategy for a better, she called for help Bing and he gave me this web site http://bestoptionstrategies.net .Now I focus on the suitable technique for themselves, and things gone up. I think everybody else faced with this particular problem. I believe my estimation will soon be helpful to you.
Read Full Q/A … :
Brother DCP J315W