Brother WP 1
Experienced technical support provide their insights in answering this question :
Your instructions saved me..I had the board off 3 times before i saw your pix….thanks so much!
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
The message “No Paper Fed” may appear on the display if the machine is out of paper, if the paper isn`t loaded properly in the paper tray, if the jam clear cover at the back of the machine isn`t install correctly, or if the white PE Actuator is missing or isn`t properly connected.
1. Causes of Multiple Sheet Feed. Multiple pages being fed through the printer overlapping or in a stack occurs when the media fails to separate correctly in the tray. Common causes are issues with the print media, incorrectly adjusted paper trays and worn or contaminated feed or separator rollers.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust.
If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary. Then reload the paper. If thick media does not feed, make sure you are loading it straight into the product, not at an angle. If paper jams when you print on both sides of the paper, try loading fewer sheets.
Adjust the paper guides in the tray to match the size of the paper. Remove the paper, smooth it out, then reload it. If the paper misfeeds, do not use that paper. Remove the moist paper, then replace it with new, dry paper.
There are different methods of paper feeding. With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.
The paper trays are overloaded. The paper is curled. The print side, or shiny side, of the paper is not loaded in the tray face down. The paper guides are too tight against the paper stack.
The paper feeding mechanism includes a drive gear coaxially coupled to a shaft of drive roller for transferring a sheet to a printing zone, a feed gear coaxially coupled to a shaft of the feed roller and operating to align the sheet transferred from the drive roller, and a discharge gear coaxially coupled to a shaft of …
The manual feed slot is located on the front of your printer. It can be closed when not in use, making the product more compact. Use the manual feed slot to print transparencies, labels, envelopes or postcards in addition to making quick runs of paper types or sizes that are not currently loaded in the paper tray.
A paper feed issue can occur for several reasons, such as dusty or contaminated paper rollers, the condition of the paper in the tray, or even issues with the software. To resolve the issue, try each solution in this document, and then use the steps in this section to print a self-test report.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
The common reasons for this issue are various, for instance, the paper input tray is overloaded, dust or moisture can affect the paper feed or paper pick rollers, the printer driver is old, etc. Thus, the printer cannot detect the paper that has been inserted into the tray.
The message “No Paper” will appear on the LCD display if the Brother machine does not detect paper in the paper tray(Tray#1 or Tray#2) or MP(Multi-purpose) Tray. Resetting the Brother machine may resolve this issue.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.
Brother Hl-2040 paper over feed
ANSWER : Your instructions saved me..I had the board off 3 times before i saw your pix….thanks so much!
Brother MFC-J6510DW extra paper tray.
ANSWER : There clearly was a similar problem couldn’t enter in to a ditch of benefit drawing up a strategy. A pal gave this http://put-call-options.com site to select an appropriate technique and I have chosen for themselves the optimum and successful naybolee. I hope I served you with your problem. Thanks for attention)))
Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.
Brother J315W – paper misfeed
ANSWER : I have the same problem: whether printing or copying, the paper feeds almost up to the print head and then stops with a paper jam error. Can’t find any bits of paper stuck anywhere. Sure would appreciate some help. DCP-J315W
Multiple paper feed
ANSWER : Most likely the pickup roller solenoid is sticking. The way it works is the solenoid energizes, pulling down a metal plate that releases the pickup roller. There is some foam on the base to quiet the clicking sound. The foam deteriorates and the plate sticks to the gooey residue. This allows the pickup roller to continue to turn instead of stopping after one revolution when the plate springs back up. That results in multiple paper being fed. Solution is to find the solenoid, which is at the end of the pickup roller shaft. Remove the sticky foam and preferably replace it with some thin sticky backed felt. You can find it at a hardware store as it is used on the bottom of chair legs.
ANSWER : Judging by your other post, you must have read that you need to remove the laser scanner assy and lubricate the spinning mirror shaft. Good luck.
Brother MFC 8220
ANSWER : This problem is normally caused by the fuser. There’s a brown driver gear who frequently broke and you’ll be obliged to replce it to take care of the problem.