Brother WP 5
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
When the WiFi light is on, your Brother machine is connected to a wireless access point. When the WiFi light blinks, the wireless connection is down, or your machine is in the process of connecting to a wireless access point.
The Paper LED flashing can be caused by no paper in the manual feed slot, a paper jam, the front cover is open, the back cover is open, dust on the drum, or not having a drum installed. Be sure that the drum unit and toner cartridge assembly is installed in the machine before continuing.
All of the LEDs flash to indicate a Service Call Error, which is a malfunction of one of the hardware components of the machine. 1. Power the machine off by holding down the POWER button.
The Drum LED blinks if the drum unit is near the end of its life. Use the drum unit until you have a print quality problem, then replace the drum unit with a new one.
If the orange light flashes at 0.5 second intervals, the printer is in Cooling mode. Wait until the Status LED stops flashing. Close the Roll Compartment Cover correctly.
Some of the causes of a blinking light on your router include outdated firmware, damaged cables, faulty components, or network outages. Restarting or resetting your router often solves these networking issues but you can also update the firmware or contact customer support.
A blinking light means you are having difficulty connecting to the internet. Ensure all telephone cable connections are tight and secure and reboot the modem and router (if applicable). POWER: A solid green light indicates the unit is properly connected to power. A blinking red light indicates a possible modem failure.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
When you see a flashing light by data that means that a print job has been released to that printer but is still processing. This typically happens when someone is printing a larger file size job.
Are you wondering why my printer is showing orange light? It indicates firmware issues, paper jams, or improperly installed cartridges. Resolve it by performing a power reset of your printer. Take out the installed cartridges.
Printer detected ink out condition (The lamp on the ink tank flashes). Stop printing, replace the ink tank, and then print again. Be sure to replace the empty ink tank before resuming printing.
The Power light blinks at a steady interval when the printer is processing a print job. If the Power light blinks fast, the ink cartridge door might be open, or the printer might be in an error state. If an error message displays on the computer screen, follow the on-screen messages to resolve the issue.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Brother HL-5370DW – All lights flash in unison
ANSWER : I just found this solution from an alternate site… (it worked for my 5370dw):
Brother HL-2040 Drum Light Driving Me Crazy!
ANSWER : Cleaning the drum unit with QTip dipped in alcohol did not get rid of the drum light. But I shined the inside of the printer and saw lots of toner. Cleaning it with the QTip dipped in alcohol where the drum unit would be inserted did get rid of the drum light! Saved me lots of money, I had bought two drum kits before to get rid of the drum light but it turned out the printer inside was dirty. So could have saved lots of money! Thanks to this forum for bringing it to my attention. So far this printer has been working for over 10 years and the parts are cheaper now.
Flashing Amber light
ANSWER : Make 1) check that the back of tray that is adjustable is against the paper and 2) the paper sensor for the tray moves freely – if it gets stuck it will cause that error.
Brother MFC 8220
ANSWER : This problem is normally caused by the fuser. There’s a brown driver gear who frequently broke and you’ll be obliged to replce it to take care of the problem.
Brother HL-2170W — 2nd sheet printing causes jam
ANSWER : I tried Angry Larry’s link to Photobucket but there’s an error message. I tried rocklobster’s link to Imageshack, but it’s for a different printer. Can someone please send me the photos to fix this issue with my Brother HL-2170W? My email is [email protected] Very much appreciated!
4F displayed on Brother 990CW printer?
ANSWER : That’s a printhead error.
Brother J315W – paper misfeed
ANSWER : I have the same problem: whether printing or copying, the paper feeds almost up to the print head and then stops with a paper jam error. Can’t find any bits of paper stuck anywhere. Sure would appreciate some help. DCP-J315W
Brother MFC-J6510DW extra paper tray.
ANSWER : There clearly was a similar problem couldn’t enter in to a ditch of benefit drawing up a strategy. A pal gave this http://put-call-options.com site to select an appropriate technique and I have chosen for themselves the optimum and successful naybolee. I hope I served you with your problem. Thanks for attention)))