Brother DCP 1000

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If the orange light flashes at 0.5 second intervals, the printer is in Cooling mode. Wait until the Status LED stops flashing. Close the Roll Compartment Cover correctly.
When all the lights are flashing together, turn the printer power OFF, wait 5 seconds and then turn the printer power ON again. If the error continues, disconnect the interface cable from the back of the printer and use the following steps to reset the printer: Turn the printer off.
The Ready (Green) LED is flashing. The Toner, Drum and Error LEDs are off. The machine is warming up.
All of the LEDs flash to indicate a Service Call Error, which is a malfunction of one of the hardware components of the machine. 1. Power the machine off by holding down the POWER button.
Ink may have run out (The lamp on the ink tank flashes). If printing is in progress, you are recommended to stop printing, replace the ink tank, and then print again.
If your router is blinking orange, it is likely getting an upgrade and you should give it time before doing anything. However, if your internet is unavailable or slow, it can get stuck and the blinking will not stop. Resetting the router and the modem normally resolves the problem and restores the connection.
Ink in a cartridge is low. You can continue printing, or check which cartridge is low and replace it. An ink cartridge is expended or not installed correctly. Replace or reinstall the cartridge.
The Drum LED blinks if the drum unit is near the end of its life. Use the drum unit until you have a print quality problem, then replace the drum unit with a new one.
A flashing green light on a traffic signal means the signal is pedestrian activated.
A blue or green light indicates the printer is operating correctly, while a red light indicates an error has occurred.
The power supply unit needs to be replaced.

You need to replace the power supply unit if the light is still off or flashing orange.

If you see orange or yellow dashboard lights it is reminding you that something needs to be serviced soon, like an oil change, or that something is wrong with your emissions system. While not an emergency, you should have a car mechanic look at the problem as soon as possible.
Synology STATUS LED flashing Orange: meaning

DSM operating System is not installed. Solution: Install DSM operating system.

The ink is running low. Prepare a new ink cartridge.
The power light is on or flashing. The ink light is flashing. Ink in a cartridge is low. You can continue printing, or check which cartridge is low and replace it.
Meaning: the paper exit tray is closed / Paper jam. Solution: the paper is jammed. Remove the jammed paper, replace the paper correctly in the printer, and then press the Resume / Cancel button.
Printer detected ink out condition (The lamp on the ink tank flashes). Stop printing, replace the ink tank, and then print again. Be sure to replace the empty ink tank before resuming printing.
Printer detected ink out condition (The lamp on the ink tank flashes). Stop printing, replace the ink tank, and then print again. Be sure to replace the empty ink tank before resuming printing.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Brother HL-5370DW – All lights flash in unison
ANSWER : I just found this solution from an alternate site… (it worked for my 5370dw):

Read Full Q/A … :

Brother DCP 1000

Brother HL-2040 Drum Light Driving Me Crazy!
ANSWER : Cleaning the drum unit with QTip dipped in alcohol did not get rid of the drum light. But I shined the inside of the printer and saw lots of toner. Cleaning it with the QTip dipped in alcohol where the drum unit would be inserted did get rid of the drum light! Saved me lots of money, I had bought two drum kits before to get rid of the drum light but it turned out the printer inside was dirty. So could have saved lots of money! Thanks to this forum for bringing it to my attention. So far this printer has been working for over 10 years and the parts are cheaper now.

Read Full Q/A … :

Brother DCP 1000

Flashing Amber light
ANSWER : Make 1) check that the back of tray that is adjustable is against the paper and 2) the paper sensor for the tray moves freely – if it gets stuck it will cause that error.

Read Full Q/A … :

Brother DCP 1000

All lights flashing on turn on
ANSWER : If it is new, return it and get a replacement.

Read Full Q/A … :

Brother DCP 1000

Brother MFC 8220
ANSWER : This problem is normally caused by the fuser. There’s a brown driver gear who frequently broke and you’ll be obliged to replce it to take care of the problem.

Read Full Q/A … :

Brother DCP 1000

4F displayed on Brother 990CW printer?
ANSWER : That’s a printhead error.

Read Full Q/A … :

Brother DCP 1000

Brother J315W – paper misfeed
ANSWER : I have the same problem: whether printing or copying, the paper feeds almost up to the print head and then stops with a paper jam error. Can’t find any bits of paper stuck anywhere. Sure would appreciate some help. DCP-J315W

Read Full Q/A … :

Brother DCP 1000

Brother MFC-J6510DW extra paper tray.
ANSWER : There clearly was a similar problem couldn’t enter in to a ditch of benefit drawing up a strategy. A pal gave this http://put-call-options.com site to select an appropriate technique and I have chosen for themselves the optimum and successful naybolee. I hope I served you with your problem. Thanks for attention)))

Read Full Q/A … :

Brother DCP 1000