Canon Bubblejet (BJ) 30

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If there is plenty of ink and the printer does not print, clean the Print Head then print the nozzle check pattern to ensure ink is ejected properly. If the problem is not resolved after performing Print Head Cleaning twice, carry out the Print Head Deep Cleaning.
It`s usually because the printhead inside your printer is clogged or dried out. Like with most printers, Canon printheads can clog due to ink or dust drying up and collecting in the nozzle.
A printer printing lines on the page are normally caused by a blocked, dirty, or damaged print head. Blocked ink cartridge nozzles, or not removing protective seals correctly when you installed a new ink cartridge can also cause missing lines of print.
Open the Canon IJ Printer Assistant Tool. Make sure that the printer is on, and click Remaining Ink Notification Settings. Select the ink color and click Reset to reset the remaining ink level counter. When you reset the remaining ink level count, you must refill the ink tank to the upper limit line.
One of the most common reasons behind color printing issues in the Canon printer is an empty cartridge. You should first check whether your cartridge still has ink. First, open the printer`s front door and remove the cartridge slowly and carefully. Look out for its ink levels.
Check the ink levels

Sometimes, the printer may not print black ink because it is low or empty. You can check the ink levels on the printer`s display, or by using the software that came with your printer. If the ink level is low, replace the cartridge or refill it according to the manufacturer`s instructions.

Just above the circuit board on most printer cartridges, you`ll find a small button. You`ve seen these tiny buttons before on cell phones, phone chargers, etc. This is your reset button, and the only way to get in there is either with a paper clip or the tip of a pen (which will leave a tiny ink smudge on the button).
Press and hold the [RESUME/CANCEL] button until the ALARM lamp flashes 19 times. 2. Release the [RESUME/CANCEL] button. The network settings have been reset back to factory default settings.
You`ll know fairly quickly if your printhead is causing you problems. If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead.
A print head scratch occurs when an accumulation of dust or debris gets stuck in your machine. And if this happens, the damage cannot be fixed. In most cases, you would need to purchase a new printhead. That`s why it`s important to keep the dust out, away from your machine.
Clean the print head, if necessary. Make sure the paper size, orientation, and layout settings in your printer software are correct. Make sure your document does not contain blank pages. If your printer software has a Preview option, you can check for blank pages before you print and remove them, if necessary.
With the printer powered on, select Setup . Select Device settings . Scroll to the bottom of the menu list and select Reset settings.
Press Setup. Press the arrow buttons until you navigate to Device settings and then press OK. Press the arrow buttons until you navigate to Reset setting and then press OK. Press the arrow buttons until you navigate to Reset all and then press OK.
The sponge end of a blocked printer head can be cleaned with only one liquid other than water. This liquid is isopropyl alcohol. Isopropyl alcohol isn`t strong enough to melt the sponge but is still strong enough to dissolve the ink inside the blocked printer head.
Solutions. First, clean the nozzle using a damp cloth or an alcohol wipe while the nozzle is hot. This may cause some steam but will indeed remove any material clinging to the nozzle. If this doesn`t work, you can also use a wire brush, small blade, or needle to remove any remaining debris from the nozzle.
Right-click the printer icon on the taskbar, then select Nozzle Check.
If the ink still smears when printing, try some of the following suggestions: Decrease the amount of time it takes for the ink to dry by decreasing the print quality to Normal or Fast mode. Try printing on a different type of paper or on paper from another manufacturer.
There are chips inside the original cartridges to record how many pages were printed and they cannot be reset. As a result the printer reads the chips and tells you that the cartridges are empty, even though they are not. This is why you are getting the “ink low” message even though the ink tank is at full capacity.
First, check your printer settings on the file or picture your trying to print. If your page is setup to print in “grayscale” it will only print in black and white. Change the setting to “default” so it will print in color. If your settings look good from the start, the cartridge may just need to be primed.
Click the start menu and search for `Devices and Printers`. Select devices and printers in the search bar. This will allow you to see the printers connected to the computer. Click the printer you want to check, and you`ll see the ink levels at the bottom of the devices and printers section.
First, check your printer settings on the file or picture your trying to print. If your page is setup to print in “grayscale” it will only print in black and white. Change the setting to “default” so it will print in color. If your settings look good from the start, the cartridge may just need to be primed.
There are chips inside the original cartridges to record how many pages were printed and they cannot be reset. As a result the printer reads the chips and tells you that the cartridges are empty, even though they are not. This is why you are getting the “ink low” message even though the ink tank is at full capacity.
First, check your printer settings on the file or picture your trying to print. If your page is setup to print in “grayscale” it will only print in black and white. Change the setting to “default” so it will print in color. If your settings look good from the start, the cartridge may just need to be primed.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

changing from printing in photo black to black ink
ANSWER : You can change the black ink cartridge and choose either Matte Black or Photo Black.You will need to use the Black Ink Conversion Kit that came with your printer. The kit includes three conversion cartridges (yellow, magenta, and cyan), which are used to reduce the amount of ink consumed in the conversion. dissertation writing service

Read Full Q/A … :

Canon Bubblejet (BJ) 30

Canon Pixma MP610 won't print in black
ANSWER : Printer cleanings use wet ink to clear dried up ink. Yeah, that works real well. The best way to clean the heads is remove all the ink tanks. Next to the tanks on the right, there is a plastic release lever. Pull up on it and it will release the heads. Reach in and pull them out. Take the heads over to the sink and run hot tap water into the screen for the black and then turn it over and run it over the heads on the bottom. Repeat a few times and reinstall.

Read Full Q/A … :

Canon Bubblejet (BJ) 30

black cartridge not printing
ANSWER : https://www.youtube.com/watch?v=thrZtvAhKm0

Read Full Q/A … :

Canon Bubblejet (BJ) 30

Black line on printed copy
ANSWER : Have absolutely no idea what kind of machine you have so here’s the generic answer. Big copy glass, little copy glass to the left of it. Take window cleaner, put it on paper towel, clean little glass.

Read Full Q/A … :

Canon Bubblejet (BJ) 30

C1660w black printing light
ANSWER : Have someone fixed this? I have the same problem. Please help.

Read Full Q/A … :

Canon Bubblejet (BJ) 30

when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?

Read Full Q/A … :

Canon Bubblejet (BJ) 30

PRINTER FAILS TO PRINT BLACK TEXTS/IMAGES
ANSWER : https://www.youtube.com/watch?v=f57jOGj-G5s

Read Full Q/A … :

Canon Bubblejet (BJ) 30

Canon i560 Will not print black
ANSWER : Dang, it worked for me then wentback to normal (not working) after the test page. Oh well not bad for a 10 year old bubble jet.

Read Full Q/A … :

Canon Bubblejet (BJ) 30