Epson Stylus Color 860

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

if you have all lights flashing and your inkjet Epson printer reporting a possible paper jam or fatal error but there is no paper jammed in the printer maybe the problem is the light sensor first of all look at the waste ink pad counter to make sure the problem isn`t the waste ink pad try to change all ink cartridges …
The Power light blinks at a steady interval when the printer is processing a print job. If the Power light blinks fast, the ink cartridge door might be open, or the printer might be in an error state. If an error message displays on the computer screen, follow the on-screen messages to resolve the issue.
An ink cartridge is low. Make sure you have a replacement cartridge.
If the light and the light flash simultaneously, the printer is in a connection error status. Press the [Wi-Fi] button to clear the error, check the following items, and then perform network setup again. Check that the wireless router is turned on.
Projector Lamp is Burnt Out

If the light is flashing red or orange, you need to replace the lamp. If the projector turns on, but the image doesn`t appear, your lamp may be burnt out.

Check to see if the lamp is burned out, broken, or installed incorrectly. Reseat or replace the lamp as necessary. Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects.
Chances are that the flashing lights are an indicator that a printer component is malfunctioning. HP has a diagnostic tool called the “Print and Scan Doctor” that can help you find the broken part.
Status indicator light:

A blue or green light indicates the printer is operating correctly, while red indicates an error has occurred.

Red ink light flashes One of the cartridges is low on ink. Check the message that appears on your screen to determine which cartridge is low. Make sure you have a replacement cartridge. Red ink light is on One of the cartridges is out of ink or not installed.
This is a common issue and can arise in virtually any projector, but this issue is more common in certain models of projectors. The flickering is caused by what is called “arc wander.” The point at which the arc strikes begins to move slightly on the electrode and makes a track that the arc “wanders” along.
It is time to replace the lamp when: The projected image gets darker or starts to deteriorate. The message LAMP REPLACE appears on the screen when the lamp comes on and the lamp warning light is flashing orange. To maintain projector brightness and image quality, replace the lamp as soon as possible.
Yes, you can reset the print settings to their original, default values. Press and hold down the Cancel button for 3 seconds. When the message to reset the printer to default settings appears, press OK to reset the print settings.
If the error light is flashing, you cannot clean the print head. Replace the appropriate ink cartridge first. Right-click the printer icon on the taskbar, then select Head Cleaning. Or access the printer software, then click the Utility tab and click the Head Cleaning button.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Epson R2400 flashing top two lights.
ANSWER : right..i had thisroblem and have fixed it..take rear cover off .looking from back..there is a small black sensor that had come loose.. reafix..and all working good

Read Full Q/A … :

Epson Stylus Color 860

Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT

Read Full Q/A … :

Epson Stylus Color 860

Epson Stylus Photo R200 – flashing red lights
ANSWER : The R800 will flash the ink and paper lights alternately when the ink pads are assumed to be full from extensive head cleaning. Sometimes, if not always, the head will lock into place on the right side above the ink head cleaning sponges that release ink to the lower ink pads.To correct the problem you need to clean the sponge area, I use cotton swabs. If the head is locked to need to release the carriage lock with a screwdriver. This will require removing the cover, but not necessarily the bottom of the unit.There is a 179 page service manual available for download for $16.50. There are free downloads of this manual, but usually are missing the 100 pages.You can remove the cover by:1. Remove the three screws on the rear housing (One to the left of the power plug, one on the opposite side and one in the lower middle bottom.2. Remove the three screws inside the upper housing (Just under the lid where the hinge is).3. Remove the screw under the left and right side in back below the vents.4. In the back pull the white ribbon closest to you out of the block, do not try to remove the block itself.5. Place a screwdriver into the slot both on the right and lift of the bottom corners on the back to release the hooks that hold the upper unit.6. Lastly, put a screwdriver into the notches on the bottom of the printer located in the front right and left, they are spring loaded.7. Remove cover.8. The head lock release screw is in the right side of the printer and is partially covered by the lower housing. I drilled a half inch hole into the side as to be able to insert a screwdriver. Turn the screw to the left and the head will rise out of the locked position. You only need to turn enough to release the head.9. Clean the sponges and any areas you see with excess ink.10. Place the cover on the unit enough to plug the white ribbon back in and turn the unit on.If the printer lights stop flashing then you are all set.

Read Full Q/A … :

Epson Stylus Color 860

ALL LIGHTS FLASHING
ANSWER : Read this thread, it mostly pertains to the 760 model, but you might find something there that will work with your model.

Read Full Q/A … :

Epson Stylus Color 860

All lights flashing on turn on
ANSWER : If it is new, return it and get a replacement.

Read Full Q/A … :

Epson Stylus Color 860

Epson printer can't recognize Epson ink cartridge
ANSWER : Hi, my name is Jim.

Read Full Q/A … :

Epson Stylus Color 860

Epson Stylus C90 (Red Light Continuously Blinks)
ANSWER : It looks like General Error occurs. Check for foreign objects inside the printer which may block the movement of printhead carriage, paper feed, etc.

Read Full Q/A … :

Epson Stylus Color 860

My epson wf-3640 has two flashing blue lights going and will not print on command?
ANSWER : I think it is illicit anticompetitive behavior both quick essay service here in Australia and likely in different purviews too for them to look to cripple non specific ink use – and now it turns out it impairs their own particular ink and printer as well.

Read Full Q/A … :

Epson Stylus Color 860