Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Cause: Paper is jammed inside the printer. Remedy: Remove the jammed paper and set the paper cassette and covers to the original position.
Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.
At times, a related message such as a “13.01 Paper Jammed in Tray 2” which indicates that the paper did not arrive at the pre-feed sensor (PS102) in the amount of time allotted by the DC Controller. There may also be other messages such as the “13.20 Jam In Top Cover Area” or the “13.03 Paper Jam”.
Sometimes a paper jam error persists even though there is no jammed paper (false paper jam). Reset the printer, which might clear a false paper jam error, and then try to print again.
What is Error Code 13? Simply put, error code 13 is when a customer or employee enters an invalid purchase amount. This happens when a negative or illegible symbol is entered by accident or because of another typo.
Type Mismatch (Error 13) occurs when you try to specify a value to a variable that doesn`t match with its data type. In VBA, when you declare a variable you need to define its data type, and when you specify a value that is different from that data type you get the type mismatch error 13.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
A 13. FF. FF error is related to jams in the paper path. These errors indicate that the product powered up with a jam.
This means the scanner is not communicating with the scale. Make sure that there is nothing plugged into the Scale RS232 to Host port.
It means that the high limit or flame rollout switch is open. This can lead to error code 13, Limit Circuit Lockout. Error 13 means that the limit or flame rollout has been open for more than 3 minutes. To address this issue, we need to ensure the furnace has proper air flow, and increase it if necessary.
Code 13. What it means: This code usually signifies a limit switch lockout. This switch is also a safety feature that engages when there`s a malfunction in lighting the furnace burners. If the burners fail to ignite after three attempts, the switch flips and cuts off any gas flow to the burner.
Displaying of the error code “err 13”. The heat pump does not start. Origin of the problem : This problem corresponds to an excessive air temperature (greater than 43°C).
Once the printer believes the cartridge has run out of ink you will be presented with either the E13 message or the E16 message that indicates that you need to change the ink cartridge. If this message is being displayed on your printers screen then your printer will stop printing and scanning.
1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.
Common factors include driver problems, software issues, hardware failures and overuse.
This jam occurs when residual paper is detected at the Tray 2 feed sensor (SR11). Open Tray 2, remove any jammed paper, and then close the tray. Open and close the upper right door to allow the printer to attempt to clear the jam.
According to technical documentation this error is usually caused when trying to print on a unit that had either an internal or external finisher and that device has been removed, without replacing the flag assembly that is used for standard output bin.
The event code: 13. B9. FF indicates that the printer believes there is a jam at the fuser output sensor, at power on. That means that printer has been power cycled, and the printer detects paper under the fuser output sensor while checking during the boot process.
If it is only the 30.1. 13, this means there is a scan ASIC (application specific Integrated Circuit) hardware error. The ASIC resides on the Scanner control board. Typically a technician is disbatched with that type of service.
For example; a 13. A2. D2 indicates that the paper jammed before reaching the tray 2 feed sensor when pulling paper from tray 2. In this case you would look for any jammed paper in or behind tray 2.
When a 31.13. 13 error appears on the control panel, it indicates that there is a jam in the document feeder because the feeder cover is open. Open then close the document feeder cover. If issue remains, open the document feeder cover.
When a 13. E1. D2 Error appears on the control panel, it indicates there is jam because the paper cannot exit the printer. This might be caused by damage to the output bushing.
If your printer has a paper path cover behind the carriage, remove the cover, and then remove any jammed paper. Pull out the input tray, and then remove any jammed paper. If your printer has a bottom cleanout door, carefully lift the printer and look under it, and then remove any jammed paper from the bottom cleanout.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :
Unknown Printer

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :
Unknown Printer

Printer jammed, after jam clearance there is an error message
ANSWER : I am looking for steps to isolate this issue. I don’t suspect the formatter.

Read Full Q/A … :
Unknown Printer

printer error code unable to print 4f
ANSWER : Follow these instructions:

Read Full Q/A … :
Unknown Printer

newly installed printer…can scan but cant be set as a default printer???
ANSWER : ITS AN EPSON L210…

Read Full Q/A … :
Unknown Printer

printer error fix
ANSWER : Epson 2540

Read Full Q/A … :
Unknown Printer

Difference Between Laser Printer and InkJet Printer
ANSWER : Laser uses toner which is a powder that gets melted onto the page. Inkjet uses ink that gets squirted onto the page.

Read Full Q/A … :
Unknown Printer

Printer error Oxc18a0201
ANSWER : Have no idea what model you have, but try this forum post or search through the site using your model and error.

Read Full Q/A … :
Unknown Printer