Dell Laser 1320C
Hope someone can help…
Experienced technical support provide their insights in answering this question :
You’re correct in your assumption. Those sensor arms have a peg on each side that pop into slots. I’ve never seen one pop out like that, so have never had to pop one back in. My assumption is if it popped out, you should be able to snap it back in without disassembly. The tricky part would be holding the spring in the correct position when snapping it back in. I would turn the printer on its top so it would be easier than twisting your head around to look up at the procedure.
How to Identify and Fix Common printer Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Cleaning the Color Toner Density (CTD) Sensor Inside the Printer. Ensure that the printer is turned off. Push the button on the right hand side of the printer and open the front cover (Figure 1). Clean the CTD sensor inside the printer with a clean dry cotton swab (Figure 2).
This issue might occur due to outdated drivers. You may download the driver for the printer from the support website of Dell and if it is not available for Windows 10, download it for Windows 8.1 and install it in compatibility mode. Note: This link also applies to Windows 10.
The default user name is admin, and the default password is left blank (NULL).
Check the USB device functionality on another computer
To verify if the USB device is faulty, unplug the USB device from the computer and plug it into another computer. If the device is not detected and is not working on another known-good computer too, the USB device is faulty.
The default BIOS password for Dell devices is “dell”. In this way, you can reset the settings and benefit from factory use again. As you can guess, this default password is publicly known or easily found by all users on the internet.
If you have not opted for secure default access to iDRAC, then the default password should be blank. In this case, the default username and password (root/calvin) apply.
Use a rocket blower and gently force air into the sensor area. Hold your camera upside down so that dust and other stuff falls out. You`ll want to blow air in multiple directions to make sure anything loose will fall out. Be careful not to hold the front nozzle too close to your sensor.
DIY sensor cleaning is completely safe. As long as you do it the right way, you shouldn`t have any problems. Many photographers regularly do their own sensor cleaning without any issues.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
Moisten a microfiber cloth with a mixture of 70% isopropyl alcohol / 30% water. The cloth should be damp, but not dripping wet. Excess moisture should be removed if the cloth is wet before wiping the product. Using any material other than a microfiber cloth could cause damage to your product.
Moisten a microfiber cloth with a mixture of 70% isopropyl alcohol / 30% water. The cloth should be damp, but not dripping wet. Excess moisture should be removed if the cloth is wet before wiping the product. Using any material other than a microfiber cloth could cause damage to your product.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
1320C – loose part into tray
ANSWER : You’re correct in your assumption. Those sensor arms have a peg on each side that pop into slots. I’ve never seen one pop out like that, so have never had to pop one back in. My assumption is if it popped out, you should be able to snap it back in without disassembly. The tricky part would be holding the spring in the correct position when snapping it back in. I would turn the printer on its top so it would be easier than twisting your head around to look up at the procedure.
Read Full Q/A … :
Dell Laser 1320C
Paper jam in tray 2 (but no paper pulled from tray) also M476DN models
ANSWER : Isopropyl alcohol is not recommended for rubber rollers. It dries out the rubber and hasten it’s cracking and breaking. It will do nothing to restore the grip. Those rollers are really hard to replace. It would be easy if that dumbass secondary menu really worked. None of the techs I’ve spoke to ever got into it. Everyone I know sends a print job and listens for the roller to rotate into position where you can pull it off.
Read Full Q/A … :
Dell Laser 1320C
Tray 1 (upper tray) paper feed problem
ANSWER : There is no way of adjusting the distance of lift. Could be that the pickup roller is worn enough that it will pick up a sheet that is higher, but not one that is lower down. You can look at the end of the roller that first makes contact and see if it is worn smooth.
Read Full Q/A … :
Dell Laser 1320C
Replacement parts: Paper tray 1 support arms
ANSWER : Try this. It’s only $7. http://www2.printerworks.com/cgi-win/tpwall.exe/find?RG5-5576-000
Read Full Q/A … :
Dell Laser 1320C
Optional 250 Sheet Feeder Tray (Q5931A – Tray 3) Constantly "Jams"
ANSWER : You don’t say if the paper moves at all. That’s key in determining the cause. If it’s not moving, then try swapping the rollers with tray 2. If it is moving out of the tray, then that would indicate there is some obstruction it is hitting on its way out of the tray. Hard to troubleshoot remotely when one doesn’t have specific details since we can’t see what is occurring.
Read Full Q/A … :
Dell Laser 1320C
Tray 2 solenoid part found under printer; Paper feed issue
ANSWER : What you are describing sound like the solenoid plate and return spring. If you look at the plate itself, you’ll see a lip curling up on one end and there are 2 slots on the sides at the other end. The lip is what stops the roller from turning until the solenoid pulls the plate down. The slots go on the 2 poles sticking up on the solenoid with the lip pointed up. Then you hook the spring on the 2 metal tabs one on the solenoid body and the other between the 2 slots at the back of the plate.
Read Full Q/A … :
Dell Laser 1320C
13.01.00 "jam in tray …" error message
ANSWER : I have never seen that problem. Really bizarre. I have to say that I’ve never replaced a main motor in any printer that I can remember and we’re talking thousands of them. I would suggest that if you have a voltmeter that you check the main motor contacts during the warm up procedure and see if they are indeed getting any voltage and go from there. If there is voltage, it’s the motor. If not, then most likely the controller board. If you don’t have a meter, it’s cheaper to buy one than start buying parts for the printer.
Read Full Q/A … :
Dell Laser 1320C
Brother MFC-J6510DW extra paper tray.
ANSWER : There clearly was a similar problem couldn’t enter in to a ditch of benefit drawing up a strategy. A pal gave this http://put-call-options.com site to select an appropriate technique and I have chosen for themselves the optimum and successful naybolee. I hope I served you with your problem. Thanks for attention)))
Read Full Q/A … :
Dell Laser 1320C